View ISL9008AIEMZ-T_8976071.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

fn6300 rev 5.00 page 1 of 12 june 27, 2014 fn6300 rev 5.00 june 27, 2014 isl9008a low noise ldo with low i q , high psrr datasheet isl9008a is a high performance single low noise, high psrr ldo that delivers a continuous 150ma of load current. it has a low standby current and is stable with 1f of mlcc output capacitance with an esr of up to 200m ? . the isl9008a has a high psrr of 65db and output noise less than 45v rms . when coupled with a no load quiescent current of 46a (typical), an d 0.5a shutdown current, the isl9008a is an ideal choice for portable wireless equipment. the isl9008a comes in several fixed voltage options with 1.8% output voltage accuracy over-temperature, line and load. other output voltage options may be available upon request. pinouts isl9008a (5 ld sc-70) top view isl9008a (6 ld 1.6x1.6 tdfn) top view features ? high performance ldo wit h 150ma continuous output ? excellent transient respons e to large current steps ? excellent load regulation: <0.1% voltage change across full range of load current ? high psrr: 65db at 1khz ? wide input voltage capability: 2.3v to 6.5v ? very low quiesc ent current: 46a ? low dropout voltage: typically 200mv at 150ma ? low output noise: typically 45v rms at 100a (1.5v) ? stable with 1f to 4.7 f ceramic capacitors ? shutdown pin turns off ld o with 1a (max) standby current ? soft-start limits input current surge during enable ? current limit and overheat protection ? 1.8% accuracy over all operating conditions ? 5 ld sc-70 package or 6 ld tdfn package ? -40c to +85c operatin g temperature range ? pb-free (rohs compliant) applications ? pdas, cell phones and smart phones ? portable instruments, mp3 players ? handheld devices inc luding medical handhelds vin gnd en vo nc 1 2 3 5 4 nc 5 vo gnd nc vin en 1 2 3 6 4 5
isl9008a fn6300 rev 5.00 page 2 of 12 june 27, 2014 ordering information part number ( note 5 , 6 ) part marking v o voltage (v) ( note 1 ) temp. range (c) package (pb-free) pkg. dwg. # isl9008aienz-t ( notes 2, 3 ) cbv 3.3 -40 to +85 5 ld sc-70 p5.049 ISL9008AIEMZ-T ( notes 2, 3 ) cbt 3.0 -40 to +85 5 ld sc-70 p5.049 isl9008aiekz-t ( notes 2, 3 ) cbs 2.85 -40 to +85 5 ld sc-70 p5.049 isl9008aiejz-t ( notes 2, 3 ) cbr 2.8 -40 to +85 5 ld sc-70 p5.049 isl9008aiehz-t ( notes 2, 3 ) cbp 2.75 -40 to +85 5 ld sc-70 p5.049 isl9008aiefz-t ( notes 2, 3 ) cbn 2.5 -40 to +85 5 ld sc-70 p5.049 isl9008aietz-t ( notes 2, 3 ) cdw 1.9 -40 to +85 5 ld sc-70 p5.049 isl9008aiecz-t ( notes 2, 3 ) cbm 1.8 -40 to +85 5 ld sc-70 p5.049 isl9008aiebz-t ( notes 2, 3 ) cbl 1.5 -40 to +85 5 ld sc-70 p5.049 isl9008airubz-t ( note 4 ) p 1.5 -40 to +85 6 ld tdfn l6.1.6x1.6a isl9008airucz-t ( note 4 ) q 1.8 -40 to +85 6 ld tdfn l6.1.6x1.6a isl9008airufz-t ( note 4 ) r 2.5 -40 to +85 6 ld tdfn l6.1.6x1.6a isl9008airuhz-t ( note 4 ) s 2.75 -40 to +85 6 ld tdfn l6.1.6x1.6a isl9008airujz-t ( note 4 ) t 2.8 -40 to +85 6 ld tdfn l6.1.6x1.6a isl9008airukz-t ( note 4 ) v 2.85 -40 to +85 6 ld tdfn l6.1.6x1.6a isl9008airumz-t ( note 4 ) w 3.0 -40 to +85 6 ld tdfn l6.1.6x1.6a isl9008airunz-t ( note 4 ) y 3.3 -40 to +85 6 ld tdfn l6.1.6x1.6a notes: 1. for other output voltages, contact intersil marketing. 2. these intersil pb-free plastic packaged products employ speci al pb-free material sets, molding compounds/die attach material s, and 100% matte tin plate plus anneal (e3 terminat ion finish, which is rohs com pliant and compatible with both snpb and pb-free soldering oper ations). intersil pb-free products are msl classified at pb-free peak reflow temp eratures that meet or exceed the pb-free requirements of ipc/je dec j std-020. 3. the part marking is located on the bottom of the part. 4. these intersil pb-free plastic packaged products employ speci al pb-free material sets; molding compounds/die attach material s and nipdau plate - e4 termination finish, which is rohs compliant and compatibl e with both snpb and pb-free soldering operations. intersil pb- free products are msl classified at pb-free peak ref low temperatures that meet or exceed the pb-free requirements of ipc/jedec j std-020. 5. please refer to tb347 for details on reel specifications. 6. for moisture sensitivity level (msl), please see product info rmation page for isl9008a . for more information on msl, please see tech brief tb363
isl9008a fn6300 rev 5.00 page 3 of 12 june 27, 2014 absolute maximum ratings thermal information supply voltage (v in ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +7.1v v o pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +3.6v all other pins . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3v to (vin+0.3v) recommended operating conditions ambient temperature range (t a ) . . . . . . . . . . . . . . .-40c to +85c supply voltage (v in ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.3 t o 6.5v thermal resistance ? ja (c/w) 5 ld sc-70 package ( note 7 ) . . . . . . . . . . . . . . . . . 231 6 ld tdfn package ( note 8 ) . . . . . . . . . . . . . . . . 125 junction temperature range . . . . . . . . . . . . . . . . .-4 0c to +125c operating temperature range . . . . . . . . . . . . . . . . .-4 0c to +85c storage temperature range . . . . . . . . . . . . . . . . . .-6 5c to +150c pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . see tb493 caution: do not operate at or near the maximum ratings listed fo r extended periods of time. exposure to such conditions may adv ersely impact product reliability and result in failures not covered by warranty. notes: 7. ? ja is measured with the component mounted on a high effective the rmal conductivity test board in free air. see tech brief tb379 for details. 8. ? ja is measured in free air with the component mounted on a high e ffective thermal conductivity t est board with direct attach f eatures. see te c h b r i e f tb379 . electrical specifications unless otherwise noted, all parameters are established over the operational supply voltage and temperature range of the device as follows: ta = -40c to +85c; vin = (v o + 0.5v) to 6.5v with a minimum vin of 2.3v; cin = 1 f; co = 1 f. parameter symbol test conditions min ( note 11 )typ max ( note 11 )units dc characteristics supply voltage v in 2.3 6.5 v ground current i dd quiescent condition: i o = 0a 46 66 a shutdown current i dds 0.5 1.2 a uvlo threshold v uv+ 1.9 2.1 2.3 v v uv- 1.6 1.8 2.0 v regulation voltage accuracy initial accuracy at v in = v o + 0.5v, i o = 10ma, t j = +25 c -0.7 +0.7 % v in = v o + 0.5v to 6.5v, i o = 10 ? a to150ma, t j = +25 c -0.8 +0.8 % v in = v o + 0.5v to 6.5v, i o = 10 ? a to 150ma, t j = -40c to +125c -1.8 +1.8 % maximum output current i max continuous 150 ma internal current limit i lim 175 265 355 ma drop-out voltage ( note 10 )v do1 i o = 150ma; v o ? 2.5v 300 500 mv v do2 i o = 150ma; 2.5v ? v o ? 2.8v 250 400 mv v do3 i o = 150ma; 2.8v ? v o 200 325 mv thermal shutdown temperature t sd+ 140 c t sd- 110 c ac characteristics ripple rejection ( note 9 )i o = 10ma, v in = 2.8v(min), v o = 1.8v at 1khz 65 db at 10khz 45 db at 100khz 35 db output noise voltage ( note 9 )v o = 1.5v, t a = +25 c bw = 10hz to 100khz, i o = 100a 45 v rms bw = 10hz to 100khz, i o = 10ma 65 v rms device start-up characteristics device enable time t en time from assertion of the enx pin to when the output voltage reaches 95% of the v o (nom) 250 500 s
isl9008a fn6300 rev 5.00 page 4 of 12 june 27, 2014 ldo soft-start ramp rate t ssr slope of linear portion of ldo output voltage ramp during start-up 30 60 s/v en pin characteristics input low voltage v il -0.3 0.4 v input high voltage v ih 1.4 v in +0.3 v input leakage current i il , i ih 0.1 ? a pin capacitance c pin informative 5 pf notes: 9. limits established by character ization and are not production tested. 10. vox = 0.98*vox(nom); valid for vox greater than 1.85v. 11. parameters with min and/or max limits are 100% tested at +25 c, unless otherwise specified. temperature limits established by characterization and are not production tested.. electrical specifications unless otherwise noted, all parameters are established over the operational supply voltage and temperature range of the device as follows: ta = -40c to +85c; vin = (v o + 0.5v) to 6.5v with a minimum vin of 2.3v; cin = 1 f; co = 1 f. parameter symbol test conditions min ( note 11 )typ max ( note 11 )units typical performance curves figure 1. output voltage vs input voltage (3.3v output) figure 2. output voltage change (%) vs input voltage (3.3v output) output voltage, v o (%) input voltage (v) -0.6 -0.2 0.2 0.6 -0.8 3.8 4.2 6.2 5.8 6.6 3.4 4.6 5.0 5.4 -0.4 0.0 0.4 0.8 v o = 3.3v +85 ? c -40 ? c +25 ? c i load = 0ma output voltage change (%) input voltage (v) v o = 3.3v i o = 0ma i o = 75ma i o = 150ma +25c 0.2 0.1 0.0 -0.1 -0.2 -0.3 -0.4 3.3 3.8 4.3 4.8 5.3 5.8 6.3
isl9008a fn6300 rev 5.00 page 5 of 12 june 27, 2014 figure 3. output vo ltage vs load current figure 4. output voltage vs temperature figure 5. dropout voltage vs input voltage (3.3v output) figure 6. dropout voltage vs input voltage (2.8v output) figure 7. dropout voltage vs load current figure 8. dropout voltage vs load current typical performance curves (continued) load current - i o (ma) output voltage change (%) 1.0 0.8 0.6 0.4 0.2 0.0 -0.2 -0.4 -0.6 -0.8 -1.0 0 25 50 75 100 125 150 175 v in = 3.8v v o = 3.3v -40c +25c +85c 0.04 0.06 -0.06 -0.10 -25 0 25 85 -40 temperature ( ? c) output voltage (%) -0.02 0.00 0.02 0.08 0.10 -0.04 -0.08 55 v in = 3.8v v o = 3.3v i o = 0ma i o = 75ma i o = 150ma output voltage, v o (v) input voltage (v) 3.4 3.3 3.2 3.1 3.0 2.9 2.8 2.7 2.6 2.5 2.4 2.3 2.6 3.1 3.6 4.1 4.6 5.1 5.6 6.1 6.6 i o = 150ma i o = 0ma i o = 75ma v o = 3.3v +25c input voltage (v) output voltage, v o (v) v o = 2.8v 2.9 2.8 2.7 2.6 2.5 2.4 2.3 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5 i o = 150ma i o = 75ma +25c i o = 0ma output load (ma) v o = 2.8v v o = 3.3v dropout voltage, v do (mv) 250 200 150 100 50 0 0 25 50 75 100 125 150 175 100 125 150 175 75 25 0 25 50 75 100 125 150 175 0 output load (ma) dropout voltage, v do (mv) v o = 3.3v 225 50 200 +25 ? c +85 ? c -40 ? c
isl9008a fn6300 rev 5.00 page 6 of 12 june 27, 2014 figure 9. ground current vs input voltage figure 10. ground curren t vs load figure 11. ground current vs temperature figure 12. turn on/turn off response figure 13. line transient response, 3.3v output figure 14. line transient response, 2.8v output typical performance curves (continued) 15 30 45 60 90 0 2.5 3.5 5.0 input voltage (v) ground current (a) 75 1.5 2.0 3.0 4.0 4.5 6.0 5.5 6.5 i o = 0a v o = 3.3v +85 ? c +25 ? c -40 ? c 100 20 0 25 50 75 100 125 0 load current (ma) ground current (a) 175 150 v o = 3.3v v in = 3.8v 40 60 80 120 140 +85 ? c -40 ? c +25 ? c 55 35 -20 0 20 60 -40 temperature ( ? c) ground current (a) 75 85 95 65 45 -30 -10 10 40 30 50 70 105 115 80 90 il = 150ma il = 75ma il = 0ma v in = 3.8v v o = 3.3v 1 3 0 2 0 100 200 300 400 500 600 700 800 0 time (s) vo(v) ven (v) 5 v o = 3.3v v in = 5.0v i l = 150ma c l = 1f 900 1000 400s/div v o = 3.3v i load = 150ma 3.6v 4.3v 10mv/div c load = 1f c byp = 0.01f 400s/div v o = 2.8v i load = 150ma 3.5v 4.2v 10mv/div c load = 1f c byp = 0.01f
isl9008a fn6300 rev 5.00 page 7 of 12 june 27, 2014 pin description figure 15. load transient response figure 16. psrr vs frequency figure 17. spectral noise density vs frequency typical performance curves (continued) 1.0 ms/div v o (10mv/div) i load 100ma 100 ? a v in = 3.8v v o = 3.3v 0.1k 1k 10k 100k 1m frequency (hz) 10 20 30 40 50 60 80 psrr (db) v in = 3.9v v o = 1.8v c load = 1f 50ma 10ma 70 spectral noise density ( ? v/ ? hz ) 2.000 1.000 0.100 0.010 0.001 10 100 1k 10k 100k 1m frequency (hz) v in = 3.9v v o = 1.8v c in = 1f c load = 1f 100a 10ma 5 ld sc-70 pin number 6 ld tdfn pin number pin name description 5 1 vo ldo output. connect a 1f capacitor of value to gnd 2 2 gnd gnd is the connection to system ground. connect to pcb gro und plane. 4 3 and 5 nc no connect. 3 4 en output enable. when this signal goes high, the ldo is turne d on. 1 6 vin supply voltage/ldo input. connect a 1f capacitor to gnd.
isl9008a fn6300 rev 5.00 page 8 of 12 june 27, 2014 typical application block diagram c1, c2: 1f x5r ceramic capacitor isl9008a vin gnd vo nc 5 4 1 2 v in (2.3 to 5v) v out c1 c2 en 3 enable off on c1, c2: 1f x5r ceramic capacitor isl9008a (tdfn) vo gnd vin en 5 4 1 2 vout c1 c2 nc 3 enable off on nc vin (2.3 to 5v) 6 vo gnd bandgap and temperature sensor uvlo vin short circuit, thermal protection, soft-start sd control logic voltage and reference generator 1.0v 0.94v 0.9v gnd + -
isl9008a fn6300 rev 5.00 page 9 of 12 june 27, 2014 functional description the isl9008a contains all circui try required to implement a high performance ldo. high performance is achieved through a circuit that delivers fast tra nsient response to varying load conditions. in a quiescent condition, the isl9008a adjusts its biasing to achieve the lowest standby current consumption. the device also integr ates current limit protection, smart thermal shutdown protection, and soft-start. smart thermal shutdown protects the device a gainst overheating. soft-start minimizes start-up input cu rrent surges without causing excessive device turn-on time. power control the isl9008a has an enable pin , en, to control power to the ldo output. when en is low, t he device is in shutdown mode. in this condition, all on-chip c ircuits are off, and the device draws minimum current, typica lly less than 0.3a. when the en pin goes high, the device fi rst polls the out put of the uvlo detector to ensure that the vin voltage is at least 2.1v (typic al). once verified, the device initia tes a start-up sequence. during the start-up sequence, trim sett ings are first read and latched . then sequentially, the bandgap, reference voltage and current generation circuitry tu rn on. once the refe rences are stable, the ldo powers up. during operation, whenever the v in voltage drops below about 1.84v, the isl9008a immediatel y disables the ldo output. when v in rises back above 2.1v (assuming the en pin is high), the device reinitiates i ts start-up sequence and ldo operation resumes automatically. reference generation the reference generation ci rcuitry includes a trimmed bandgap, a trimmed voltage reference divider, a trimmed current reference generator , and an rc noise filter. the bandgap generates a zero te mperature coefficient (tc) voltage for the regulator r eference and other voltage references required fo r current generation and over-temperature detection. a current generator provides ref erences required for adaptive biasing as well as references for ldo output cu rrent limit and thermal shutdown determination. ldo regulation and program mable output divider the ldo regulator is impl emented with a high-gain operational amplifier driving a pmos pass transistor. the design of the isl9008a provides a regulator that has low quiescent current, fast transi ent response, and overall stabili ty across all operating and load cu rrent conditions. ldo stability is guaranteed for a 1f to 4.7f output cap acitor that has a tolerance better th an 20% and esr less than 200mw. the design is performance-optimized for a 1f capacitor. unless limited by the application, use of an output capacitor value above 4.7f is not recomm ended as ldo performance improvement is minimal. soft-start circuitry integrated into each ldo lim its the initia l ramp-up rate to about 30s/v to minimize current surge. the isl9008a provides short-circui t protection b y limiting the output current to about 265ma (typ). the ldo uses an independently t rimmed 1v reference as its input. an internal resistor div ider drops the ldo output voltag e down to 1v. this is compar ed to the 1v reference for regulation. the resistor divis ion ratio is programmed in the factory. overheat detection the bandgap outputs a proportion al-to-temperature current that is indicative of the temper ature of the sil icon. this curr ent is compared with references to determine if the device is in danger of damage due to overheating. when the die temperature reaches about + 140c, the ldo momentarily shuts down until the die cools sufficiently. in the overheat condition, if the ldo sources more than 50ma it will be shut off. once the die tem perature falls back below about +110c, the disabled ldo is re-enabled and soft-start automatically takes place. exposed thermal pad the isl9008a with tdfn pack age has an exposed thermal pad at the bottom side of the package. the pcb layout should connect the exposed pad to s ome copper on the component layer for a good thermal conductivity. since the copper area on the component layer i s limited by the surrounding pins of the package, it is more effective to use some thermal vias to conduct the heat t o other copper layer s if possible. electrically, the copper and vias connecting to the exposed pad should be isolated from any o ther pin connection, they are strictly for thermal enhancement purpose.
fn6300 rev 5.00 page 10 of 12 june 27, 2014 isl9008a intersil products are manufactured, assembled and tested utilizing iso9001 quality systems as noted in the quality certifications found at www.intersil.com/en/suppor t/qualandreliability.html intersil products are sold by description on ly. intersil may modify the circuit design an d/or specifications of products at any time without notice, provided that such modification does not, in intersil's sole judgment, affect the form, fit or function of the product. accordingly, the reader is cautioned to verify that datasheets are current before placing orders. information fu rnished by intersil is believed to be accu rate and reliable. however, no responsib ility is assumed by intersil or its subsidiaries for its use; nor for any infrin gements of patents or other rights of third parties which may result from its use. no license is granted by implication or otherwise under any patent or patent rights of intersil or its subsidiaries. for information regarding intersil corporation and its products, see www.intersil.com for additional products, see www.intersil.com/en/products.html ? copyright intersil americas llc 2006-2014. all rights reserved. all trademarks and registered trademarks are the property of their respective owners.
isl9008a fn6300 rev 5.00 page 11 of 12 june 27, 2014 ultra thin dual flat no-l ead plastic package (utdfn) b d a e 0.15 c 2x pin 1 top view 0.15 c 2x reference detail a 0.10 c 0.08 c 6x a3 c seating plane l e 46 31 bottom view side view 0.10 cab b6x detail a 0.127 +0.058 a1 a1 a 0.1270.008 64 13 m co.2 1.00 ref d2 dap size 1.30 x 0.76 e2 -0.008 terminal thickness 0.30 1.00 0.45 0.50 0.25 1.25 2.00 1.00 land pattern 6 l6.1.6x1.6a 6 lead ultra thin dual flat no-lead plastic package symbol millimeters notes min nominal max a 0.45 0.50 0.55 - a1 - - 0.05 - a3 0.127 ref - b 0.15 0.20 0.25 - d 1.55 1.60 1.65 4 d2 0.40 0.45 0.50 - e 1.55 1.60 1.65 4 e2 0.95 1.00 1.05 - e 0.50 bsc - l 0.25 0.30 0.35 - rev. 1 6/06 notes: 1. dimensions are in mm. angles in degrees. 2. coplanarity applies to the exposed pad as well as the terminals. coplanarity shall not exceed 0.08mm. 3. warpage shall not exceed 0.10mm. 4. package length/package width are considered as special characteristics. 5. jedec reference mo-229. 6. for additional information, to assist with the pcb land patte rn design effort, see intersil technical brief tb389.
isl9008a fn6300 rev 5.00 page 12 of 12 june 27, 2014 small outline transistor plastic packages (sc70-5) d e 1 e e1 c l c c l e b c l a2 a a1 c l 0.20 (0.008) m 0.10 (0.004) c c -c- seating plane 4 5 123 view c view c l r1 r 4x ? 1 4x ? 1 gauge plane l1 seating ? l2 c plane c base metal with c1 b1 plating b 0.4mm 0.75mm 0.65mm 2.1mm typical recommended land pattern p5.049 5 lead small outline transistor plastic package symbol inches millimeters notes min max min max a 0.031 0.043 0.80 1.10 - a1 0.000 0.004 0.00 0.10 - a2 0.031 0.039 0.80 1.00 - b 0.006 0.012 0.15 0.30 - b1 0.006 0.010 0.15 0.25 c 0.003 0.009 0.08 0.22 6 c1 0.003 0.009 0.08 0.20 6 d 0.073 0.085 1.85 2.15 3 e 0.071 0.094 1.80 2.40 - e1 0.045 0.053 1.15 1.35 3 e 0.0256 ref 0.65 ref - e1 0.0512 ref 1.30 ref - l 0.010 0.018 0.26 0.46 4 l1 0.017 ref. 0.420 ref. - l2 0.006 bsc 0.15 bsc ? 0 o 8 o 0 o 8 o - n5 55 r 0.004 - 0.10 - r1 0.004 0.010 0.15 0.25 rev. 3 7/07 notes: 1. dimensioning and tolerances per asme y14.5m-1994. 2. package conforms to eiaj sc70 and jedec mo-203aa. 3. dimensions d and e1 are exclusiv e of mold flash, protrusions, or gate burrs. 4. footlength l measured at reference to gauge plane. 5. ?n? is the number of terminal positions. 6. these dimensions apply to the flat section of the lead between 0.08mm and 0.15mm from the lead tip. 7. controlling dimension: millime ter. converted inch dimen- sions are for reference only.

▲Up To Search▲

Price & Availability of ISL9008AIEMZ-T

	To Download ISL9008AIEMZ-T Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .